QUESTION
Regarding my abs problem, it's proving to be a temperamental one, it works then it doesn't work.
I've been checking it over several evenings to see what happens.
Over two nights the system was fine, then last night the system read a fault, just a flashing tell tale.
The car was stationary, but today when using the car to work it was fine, no light on the whole journey.
I still think it's something to do with the pressure switch and not road sensors, as the problem happens when stationary as well as moving.
I have the manual so will check the fault codes.
I haven't been able to get the Espritmon software working to produce a code, but I'm going to video the flashing light to see what sequence it produces.
I use my car all the time so nothing should get seized or stuck over the winter.
If I do have to replace then I will buy your setup.
I'm not paying Lotus prices for their replacement if it's going be up to £600, if that's the price it's gonna be when it's released next year.
I will let you know what I find out regarding the abs or whether it's fixed itself.
O.W. - UK
ANSWER
From experience, intermittent problems always prove difficult to solve.
It would be advisable to connect a pressure gauge to the high pressure system tell you exactly if its operating correctly.
Lotus Marques built a pressure test rig to understand the multiple faults on a 2000 Esprit GT3.
This Esprit was sent to us in Melbourne from a repair shop in Canberra.
This particular vehicle had multiple faults after rear-ending a WRX.
I am not sure who had been working on this Esprit but the owner obviously did know very much about brakes or safety.
The front brake pads were non-standard from a Toyota Tarago, cut down to suit the brake caliper.
There was about 2mm friction material left on the pads - this is why partly the Esprit did not stop in a hurry.
After installing the pressure test rig and gauge it was possible to quickly diagnose the ABS system which revealed the following problems -
1) The ABS high pressure switch was faulty
2) The ABS computer was faulty
3) The dashboard warning lamp control board was faulty
If you ever need to check this board, it is an interface between the ABS computer and dash warning lamps and lives behind the left-hand front speaker.
This is buried behind the dash and the only way to access it to remove speaker and glove box.
NOTE - At the time we did the work, there are no more boards available from the Lotus Factory.
I ended up reverse-engineering the board after figuring out the diagram and PCB layout - there are just a couple of unmarked transistors on the PCB.
Once the gauge was installed it allowed us to gain a very good understanding of the system operation.
I know it may seem like a lot of work but I would encourage you to build your own test rig as it is so simple.
Without first checking the high pressure system is operating correctly, you are going to find trouble-shooting this problem very time consuming.
Copyright © 2012 Lotus Marques
Regarding my abs problem, it's proving to be a temperamental one, it works then it doesn't work.
I've been checking it over several evenings to see what happens.
Over two nights the system was fine, then last night the system read a fault, just a flashing tell tale.
The car was stationary, but today when using the car to work it was fine, no light on the whole journey.
I still think it's something to do with the pressure switch and not road sensors, as the problem happens when stationary as well as moving.
I have the manual so will check the fault codes.
I haven't been able to get the Espritmon software working to produce a code, but I'm going to video the flashing light to see what sequence it produces.
I use my car all the time so nothing should get seized or stuck over the winter.
If I do have to replace then I will buy your setup.
I'm not paying Lotus prices for their replacement if it's going be up to £600, if that's the price it's gonna be when it's released next year.
I will let you know what I find out regarding the abs or whether it's fixed itself.
O.W. - UK
ANSWER
From experience, intermittent problems always prove difficult to solve.
It would be advisable to connect a pressure gauge to the high pressure system tell you exactly if its operating correctly.
Lotus Marques built a pressure test rig to understand the multiple faults on a 2000 Esprit GT3.
This Esprit was sent to us in Melbourne from a repair shop in Canberra.
This particular vehicle had multiple faults after rear-ending a WRX.
I am not sure who had been working on this Esprit but the owner obviously did know very much about brakes or safety.
The front brake pads were non-standard from a Toyota Tarago, cut down to suit the brake caliper.
There was about 2mm friction material left on the pads - this is why partly the Esprit did not stop in a hurry.
After installing the pressure test rig and gauge it was possible to quickly diagnose the ABS system which revealed the following problems -
1) The ABS high pressure switch was faulty
2) The ABS computer was faulty
3) The dashboard warning lamp control board was faulty
If you ever need to check this board, it is an interface between the ABS computer and dash warning lamps and lives behind the left-hand front speaker.
This is buried behind the dash and the only way to access it to remove speaker and glove box.
NOTE - At the time we did the work, there are no more boards available from the Lotus Factory.
I ended up reverse-engineering the board after figuring out the diagram and PCB layout - there are just a couple of unmarked transistors on the PCB.
Once the gauge was installed it allowed us to gain a very good understanding of the system operation.
I know it may seem like a lot of work but I would encourage you to build your own test rig as it is so simple.
Without first checking the high pressure system is operating correctly, you are going to find trouble-shooting this problem very time consuming.
Copyright © 2012 Lotus Marques
