The following information has been derived from the Service Parts List (Lotus part number A079T0325J) page number JB2.
NOTE CAREFULLY - A flaring allowance of 0.500" (12.70mm) has been added to the original dimensions shown in the Service Parts List.
Therefore. the following solid brake pipe dimensions are cut-lengths - this means the length that is required prior to flaring the ends of each pipe.
Be sure to install the correct fittings and check orientation prior to flaring and then bending the pipes.
Right hand front solid pipe, flexible hose to left hand caliper = 6.00" (150.00mm)
Fittings = male 10mm x 1.0mm pitch thread + female 10mm x 1.0mm pitch thread
Left hand front front pipe, flexible hose to left hand caliper = 6.00" (150.00mm)
Fittings = male 10mm x 1.0mm pitch thread + female 10mm x 1.0mm pitch thread
Front solid pipe, Master cylinder to front T-joiner = 23.5" (596.90mm)
Fittings = male 10mm x 1.0mm pitch thread + male 10mm x 1.0mm pitch thread
Front solid pipe, Master cylinder to double ended joiner = 21.5" (546.10mm)
Fittings = male 10mm x 1.0mm pitch thread + male 10mm x 1.0mm pitch thread
Right hand front solid pipe, front T-joiner to flexible hose = 20.5" (520.70mm)
Fittings = male 10mm x 1.0mm pitch thread + female 10mm x 1.0mm pitch thread
Left hand front solid pipe, front T-joiner to flexible hose = 20.5" (520.70mm)
Fittings = male 10mm x 1.0mm pitch thread + female 10mm x 1.0mm pitch thread
Main solid brake pipe front to rear, front double ended joiner to rear T-joiner = 132.0" (3352.8mm)
Fittings = male 10mm x 1.0mm pitch thread + male 10mm x 1.0mm pitch thread
Right hand rear solid pipe, flexible to T-joiner = 27" (685.8mm)
Fittings = male 10mm x 1.0mm pitch thread + female 10mm x 1.0mm pitch thread
Left hand rear solid pipe up to T-joiner = 27" (685.8mm)
Fittings = male 10mm x 1.0mm pitch thread + female 10mm x 1.0mm pitch thread
Copyright © 2012 Lotus Marques
NOTE CAREFULLY - A flaring allowance of 0.500" (12.70mm) has been added to the original dimensions shown in the Service Parts List.
Therefore. the following solid brake pipe dimensions are cut-lengths - this means the length that is required prior to flaring the ends of each pipe.
Be sure to install the correct fittings and check orientation prior to flaring and then bending the pipes.
Right hand front solid pipe, flexible hose to left hand caliper = 6.00" (150.00mm)
Fittings = male 10mm x 1.0mm pitch thread + female 10mm x 1.0mm pitch thread
Left hand front front pipe, flexible hose to left hand caliper = 6.00" (150.00mm)
Fittings = male 10mm x 1.0mm pitch thread + female 10mm x 1.0mm pitch thread
Front solid pipe, Master cylinder to front T-joiner = 23.5" (596.90mm)
Fittings = male 10mm x 1.0mm pitch thread + male 10mm x 1.0mm pitch thread
Front solid pipe, Master cylinder to double ended joiner = 21.5" (546.10mm)
Fittings = male 10mm x 1.0mm pitch thread + male 10mm x 1.0mm pitch thread
Right hand front solid pipe, front T-joiner to flexible hose = 20.5" (520.70mm)
Fittings = male 10mm x 1.0mm pitch thread + female 10mm x 1.0mm pitch thread
Left hand front solid pipe, front T-joiner to flexible hose = 20.5" (520.70mm)
Fittings = male 10mm x 1.0mm pitch thread + female 10mm x 1.0mm pitch thread
Main solid brake pipe front to rear, front double ended joiner to rear T-joiner = 132.0" (3352.8mm)
Fittings = male 10mm x 1.0mm pitch thread + male 10mm x 1.0mm pitch thread
Right hand rear solid pipe, flexible to T-joiner = 27" (685.8mm)
Fittings = male 10mm x 1.0mm pitch thread + female 10mm x 1.0mm pitch thread
Left hand rear solid pipe up to T-joiner = 27" (685.8mm)
Fittings = male 10mm x 1.0mm pitch thread + female 10mm x 1.0mm pitch thread
Copyright © 2012 Lotus Marques